12:48. Removal and installation of a forward door and holder of adjusting elements
Forward door
1 – holder
2 – bolt, 30 N • m of M8 x 26
3 – bolt, 30 N • m of M8 x 32
4 – adjusting wedge. It has to be always established
5 – door. The door can be removed also without removal of the holder of adjusting elements
6 – bolt, 30 N • m | 7 - adjusting wedge. It has to be always established
8 – guard of a side emphasis
9 – drive cable
10 – bolt, 30 N • m of M8 x 26
11 – lock draft |
REMOVAL
ATTENTION
The door can be removed also without removal of the holder of adjusting elements. In this case the holder is not required to remove.
|
PERFORMANCE ORDER |
| 1. Remove facing of a door, address the subsection Removal and installation of facing of a door. |
| 2. Remove facing of a rack And (below), address the subsection Removal and installation of facing of a rack And. | | 3. Disconnect electric wires and a vacuum hose of the uniform lock from the holder –1–. | | 4. Disconnect a cable –9– from the holder. | | 5. Turn out bolts (2, 3, 6 and 10). At the same time remove adjusting wedges-4-and-7-. |
| 6. Take out the holder of adjusting elements up. | | 7. Remove a casing between a door and a rack And. | | 8. Remove the plug at a rack And. | | 9. Take out electric wires and a vacuum hose of the uniform lock from a rack And. |
| 10. Disconnect electric wires and a vacuum hose at A. Otsoyedinite's rack the plug of a hose of the uniform lock, address subsection the Uniform lock – general information and vacuum hoses. | | 11. You watch that the socket did not slide off in A. Zakrepite's rack his clothespeg. |
| 12. Ask the assistant to support a door. | | | 1 – the bolt, is established from within, 30 N • by m
2 – door loop top
3 – cover, 23 N • m
4 – bolt, 30 N • m
5 – Torx screw, 30 N • m | 1 - the loop is lower
2 – the door is forward
3 – bolt, 30 N • m
4 – Torx screw, 30 N • m
5 – bolt, 30 N • m | | 13. Unscrew Torx T45 screws from a door at loops from above and from below. |
| 14. Remove a door by means of the assistant. |
|
INSTALLATION
|
PERFORMANCE ORDER |
| 1. Establish a door by means of the assistant in loops and fix by Torx T45 screws. Moment of an inhaling of 30 N • m. |
| 2. Insert electric wires and a vacuum hose of the uniform lock into the socket of a rack And. | | 3. Insert electric wires and a vacuum hose into a rack And. | | 4. Fix plugs in a rack And. | | 5. Insert a casing between a door and a rack And. | | 6. Enter the holder from above into a door. | | 7. Fix the holder by bolts. Do not forget about adjusting wedges of bolts-3-and-6-, address an illustration. Sequence of an inhaling: (2, 10, 6, 3). Moment of an inhaling of 30 N • m. Adjustment of wedges is considered in the subsection Adjustment of a Door. | | 8. Connect a cable –9– to the holder. | | 9. Connect electric wires and a vacuum hose of the uniform lock, lay them and fix, address subsection the Uniform lock – general information and vacuum hoses. | | 10. Adjust a door. | | 11. Establish facing of a rack And, address the subsection Removal and installation of facing of a rack And. | | 12. Establish facing of a door, address the subsection Removal and installation of facing of a door. | |