13:15. Replacement of lamps of external lighting
PERFORMANCE ORDER |
1. Switch off the switch of the corresponding lamp. | 2. Switch off ignition. | |
Near and far light
ATTENTION Lamps of H7 are under pressure and can burst when performing their replacement. Therefore when replacing lamps of H7 it is necessary to use mittens and goggles.
PERFORMANCE ORDER |
1. Open a cowl. |
| 2. Uncover behind a headlight. For this purpose press both levels –1– down and disconnect them from holders –2–. Cast away a cover –3– above back and take out from the lower guides. |
| 3. Rasstykuyte I will corrode lamps of passing beam-3-or driving beam-4-. 1 – the electric motor of adjustment of range of light, 2 – I will corrode headlights. | 4. Raise from a reverse side of a headlight a spring clip in the center a little and incline it in the direction of an arrow. | 5. Rasstykuyte I will corrode lamps of passing beam. | 6. Press and open a spring clip over a lock pad. | 7. Take out a lamp from a reflector. ATTENTION
Do not take a lamp naked fingers. The fingerprint evaporates and besieged on a reflector, reducing a light stream of a lamp. Surely establish a lamp of the same execution. Spots on a lamp are eliminated with the pure scarf moistened in alcohol. |
8. Insert a new lamp so that pads entered the corresponding grooves on the case. | 9. Cast away a spring bracket back and record in pads. | 10. Join the socket on the boss. | 11. Put a cover on a reverse side of a headlight and record a spring clip. |
12. Check adjustment of headlights in conditions HUNDRED. | 13. Close a cowl. |
|
Parking light
PERFORMANCE ORDER |
1. Open a cowl. |
2. Uncover behind a headlight. For this purpose above press both plastic levels down and release them. Cast away a cover back. | | 3. Take out a cartridge –1– with a lamp from a reflector. 2 – plug of driving beam. |
4. Take out a lamp from the boss. |
5. Insert a new lamp into a cartridge. |
6. Press a cartridge with a lamp into a reflector against the stop. | 7. Connect a cover on a reverse side of a headlight below and record it above. | 8. Close a cowl. | |
Forward index of turn
PERFORMANCE ORDER |
1. Remove a forward signal of turn, address the subsection Removal and installation of the forward index of turn. | | 2. Turn a cartridge of a lamp –1– to the left and take out it from the case-3-. | 3. Slightly press a lamp –2– into a cartridge, turn on 90 ° (1/4 turns) to the left and take out a lamp. ATTENTION Do not touch a flask of a new lamp by hand fingers. Use a pure rag or put on thin gloves. | 4. Insert a new lamp, slightly press on it and turn to the right. |
5. Insert a cartridge with a lamp into a reflector and turn to the right. ATTENTION
The cartridge has to be recorded.
| 6. Establish the index of turn, address the subsection Removal and installation of the forward index of turn. | |
Side repeater of the index of turn
PERFORMANCE ORDER |
| 1. Press fingers the index of turn in the direction of a headlight forward (an arrow illustrations) and take out it in a back part from an opening in a wing –3–. At removal the lamp is displaced forward, overcoming force of a plastic spring –4–. | 2. Remove a cartridge of a lamp –5– from the case-6-. | 3. Take out a lamp from the boss and replace. | 4. Insert a cartridge with a lamp into the case. | 5. Insert a lamp behind into plastic hooks in a wing opening, on the other hand press and record a plastic spring. |
| |
Back lamp
PERFORMANCE ORDER |
1. Open a back door. |
2. Open a luggage carrier pocket at the left or on the right. For this purpose turn a clip above at a pocket cover on the left. |
| 3. Rasstykuyte socket of a-3-back lamp. | 4. Squeeze lock levels –2– and thus release the holder of a lamp. |
5. Take out the holder of a lamp –1–. |
6. Slightly press the damaged lamp into a cartridge, turn on 90 ° (1/4 turns) to the left and take out. ATTENTION
Insert a new lamp, slightly press it and turn to the right. | 7. Insert the holder of a lamp into a back lamp, press and record. |
8. Join the socket at the holder of a lamp. |
9. Close a cover of a pocket of a luggage carrier and record a clip turn to the right. | 10. Close a back cover. | |
Lamp of illumination of registration plate
PERFORMANCE ORDER |
1. Open a back door. |
| 2. Turn off in a level –1– on two screws with crosswise vents –3–. On an illustration the lighting lamp of the right registration plate is represented. | 3. Take out the holder of a lamp from a level and a rasstykuyta the socket-2-. | 4. Take out a lamp –4– of the boss and replace. At the same time you watch reliability of installation of a lamp. If necessary slightly turn in clips. | 5. Join the socket. | 6. Insert the holder of a lamp into a level and fix by screws. | 7. Close a back door. | |
Additional stoplight The additional stoplight is located at the top of a back door behind back glass.