1. Rotation can be carried out at emergence of signs of uneven wear of protectors. However you remember that in case of successful rotation of all four wheels you eventually should replace all tires at the same time.
As holding this procedure demands a car raising above the ground and removals of wheels, check at the same time and operation of brake mechanisms. |
ATTENTION Even if you are not going to make rotation, at least check reliability of an inhaling of bolts of fastening of wheels.
|
| 2. At more bystry wear of forward tires it is recommended to interchange the position of forward and back tires. Thus, service life of all four tires is equalized. |
| 3. Address information in Poddomkrachivaniye's subsection and towage for the correct raising of the car and change of a wheel. |
| 4. The car should be lifted the winch or to install it on support that all four wheels were lifted above the ground. Make sure that the car is reliably fixed! |
Remarks on security measures
Do not replace separately any tire. It is necessary to replace tires on one bridge completely. Tires with a bigger depth of a protector are installed on forward wheels. Forward and back wheels have to have tires of the identical size and type, and at all-wheel drive cars also of one manufacturer and one execution of a protector. Sheena, worked more than 6 years, it is necessary to apply only in case of accident, at the same time it is necessary to be careful when driving. During the replacing and removal of tubeless tires it is necessary to change the gate surely. |
|
5. In case of use of tires with the protector assuming the movement only in a certain direction that is specified by an arrow on the side surface of the tire the specified direction needs to be observed. Only thus achievement of necessary road qualities of the car, namely hydroplaning, stability on the road, the low noise level and low wear is provided. If the spare wheel owing to accident has to be established with an opposite direction of rotation, such application has to be only temporary since achievement of the road qualities of the car stated above at the same time is impossible. It especially belongs to movement along the wet road. Therefore it is recommended to coordinate the speed of the movement with conditions of the road and to reinstall the tire according to the set direction of rotation. |
| Spare wheel |
| 6. The spare wheel can be established both on a lobby, and on a back axis. |
| 7. The spare wheel is intended only for short-term use and it should be replaced with usual as soon as possible. |
| 8. After installation of a spare wheel pressure in its tire has to make 4.2 bars. |
| 9. With the established spare wheel it is impossible to exceed the speed of 80 km/h. It is necessary to avoid the maximum acceleration of the car, intensive braking and sharp turns. |
| 10. At installation of a spare wheel the road gleam under the corresponding axis decreases approximately by 30 mm. |
| 11. It is not necessary to apply spare wheels from cars of other types. |
| 12. It is not allowed to establish two or more spare wheels. |
| Replacement of wheels |
| 13. Take off a decorative cap of a wheel. For this purpose use mount and a wire bracket from tool kit. The wire bracket is established on an opening of a cap or on an edge. Miss mount through a bracket and, having pulled mount from a wheel, take off a cap. |
| 14. On the car standing on the earth tighten the emergency brake and weaken bolts of fastening of a wheel. |
| 15. Lift the relevant party of the car and fix on supports. |
|
|
| 16. Turn off the top bolt of fastening of a wheel and on its place screw an adjusting pin. Use of an adjusting pin facilitates installation of a spare wheel. |
ATTENTION Disks from light alloys are protected from corrosion by a transparent varnish. Be careful not to damage a varnish covering. At damage of a covering, cover a disk with a varnish coat.
|
| 17. For an exception of "prikipaniye" of disks of wheels to a nave, before installation of a wheel, apply a thin film of lubricant on the nave fillet aligning a wheel disk. |
| 18. Galvanized wheel bolts can be applied only on capital stamped disks. |
| 19. Disks from light alloys fasten only the chromeplated wheel bolts on which there is a conic rotating washer. This washer established under a bolt head protects a disk surface when tightening bolts. |
| 20. Before a vvinchivaniye do not grease a carving of bolts of fastening of a wheel. |
| 21. Standard bolts of fastening of wheels have the M14 sizes x 1.5 x 27.5. Size of a turnkey head of 17 mm. |
| 22. You make tightening of bolts of fastening of a wheel evenly in several stages in the diagonal sequence. |
| 23. Moment of tightening of bolts of fastening of a wheel of 120 Nanometers. |
| Antisliding chains |
| 24. Chains have to be established only on forward wheels as well the all-wheel drive car. |
| 25. Chains of antisliding can be installed only on tires by dimension 195/65 R 15. Installation of chains of antisliding on an emergency wheel for technical reasons is not allowed. |
| 26. It is necessary to use only close-meshed chains acting no more than on 15 mm (including castle links). |
| 27. At installation of chains of antisliding it is necessary to take off full-size caps of wheels and decorative rings of disks. For safety reasons wheel bolts have to be protected by special caps. |
| 28. Before the movement on the site of a way, free from snow, it is necessary to remove antisliding chains. They worsen road performance of the car, increase wear of tires and quickly collapse. |